How To Light The Pilot Light On A Water Heater

How To Light The Pilot Light On A Water Heater. You should also see an arrow on the control knob. On a modern rheem gas water heater, it is very easy to light the pilot light.

How to Light a Water Heater Pilot Light from www.mrrooter.ca

Turn the control knob or dial to ‘pilot.’ to light a gas water heater with electronic pilot, locate the pilot light control knob in the water heater gas control assembly. This is because when power is turned off, the pilot light goes out. Once lit you will need to hold the button down for a while to ensure that it keeps burning.

Source: www.greatpros.com

Put the cover back on: Turn the control valve to “on”.

Source: kenmorewaterheater.blogspot.com

Now, hold the pilot dial down while you light the burner. Before you relight your pilot light, the first step is to turn off the gas.

Source: www.youtube.com

Keep pressing the ignition button once per second while holding the gas control knob down. Pressing down on the dial and clicking the igniter button.

Source: www.angi.com

Turn the pilot light control knob to the on. Sniff around the pilot light area and make sure you don’t smell any gas.

Source: www.youtube.com

This whole process will take approximately 1 minute for a newly installed unit. Adjust the control knob to the on position.

Source: www.appliancevideo.com

Set the thermostat dial to the “pilot lighting” place. Keep pressing the ignition button once per second while holding the gas control knob down.

Source: designachair.blogspot.com

When you want to light an electric pilot on your water heater, it’s recommended that you first switch off the electricity at the breaker. The knob should be labeled in a clear and understandable manner.

Source: www.mixedmartialarts.com

After that, set your temperate knob to low. You must have the pilot lit and the burner on to test for leaks, so that gas is flowing through the large tube.

Source: www.youtube.com

Sniff around the pilot light area and make sure you don’t smell any gas. Switch the knob back to on:

Source: www.youtube.com

Occasionally, the pilot light on your a.o. Then, push the button back down and hold it down for about five minutes.

Source: www.autumnwalk.com

Keep holding down the pilot knob or button for at least a minute after the flame ignites. Here here’s how to light the pilot light on a rheem gas water heater.

Source: www.youtube.com

Next, i’m going to continue to press and hold the dial in the pilot setting and also start to press the igniter button below it. You can find it on the gas valve’s handle, underneath the burner compartment panel.

Put The Cover Back On:

Dial or rotate the gas control knob to the pilot position. Locate the gas valve on your hot water heater and turn it to the “off” position. You should also see an arrow on the control knob.

You Will Hear The Clicking Sound Of The Igniter Sparking.

Here here’s how to light the pilot light on a rheem gas water heater. If the light starts to flicker, or goes out, then it would be time to troubleshoot the problem. Keep an eye on the status light and keep going with the process until it starts to blink.

If You Have A New Water Heater, Then You May Need To Keep Going With This For 60 Seconds.

It’s easy to turn your water heater pilot back on. Steps to relight the pilot light. Switch the gas knob to “on”:

Keep Pressing The Ignition Button Once Per Second While Holding The Gas Control Knob Down.

Then, push the button back down and hold it down for about five minutes. Depress and hold down the pilot set button or gas control knob. After 60 seconds, release the pilot button and turn the knob back to “on.”.

You Can Find It On The Gas Valve’s Handle, Underneath The Burner Compartment Panel.

Pressing down on the dial and clicking the igniter button. Then, pull out the panel and insert the flame source underneath the orifice in the pilot supply line. But first, check for a gas leak.